|Version 12 (modified by igloo, 4 years ago) (diff)|
GHC libraries and other packages
As well as the GHC repository itself, there are a number libraries and other packages that make up a GHC tree. This page describes the process by which those libraries can be altered.
Packages for which we use the upstream repository directly
In the case of
we use the main repository directly. Therefore changes can be pushed directly, as with GHC patches.
When making a change to a library, you must also update the version number if appropriate. Version number in the repositories should be maintained such that, if the library were to be release as-is, then they would have the correct version number. For example, if the last release of a library was 22.214.171.124 and you remove a function from it then, as per the Package versioning policy, the version number should be bumped to 126.96.36.199. If it is already 188.8.131.52 or higher then no further change is necessary. In order to make this easier, the version line in the .cabal file should be followed by a comment such as
-- GHC 7.6.1 released with 184.108.40.206
Packages for which there is a separate upstream repository
In the case of
there is a separate upstream repository.
The process for updating these is a little more complicated, motivated by the following objectives:
- Any changes needed by GHC should be made not only in our repository, but also in the upstream repository.
- Being used in a GHC tree should not make life harder for the upstream maintainer.
Note that these two objectives are to some extent in conflict: If a change in GHC or one of its libraries requires a change in a library with an upstream repo then, in order to satisfy objective 1, the maintainer would need to apply the patch, but if doing so is currently inconvenient for them then this would fail objective 2. This policy therefore tries to find the best compromise, without being too onerous for any party.
For these repositories, we use a "git submodule" rather than a normal repository. Using submodules means that the repository doesn't need to follow a linear path through the git history, but can instead jump around, for example from a release commit on one branch to the next release commit on a different branch.
From the GHC developer's point of view
If you are not modifying these packages then you don't need to do anything special: A regular ./sync-all pull will update the submodules as normal. However, you may find it useful to run
git config --global diff.ignoreSubmodules dirty
or each time you run git status or git diff, git will check for changes not only in the GHC repository, but also in all the submodules. (you must have git >= 1.7.3 for this to work).
If you need to modify one of these libraries, then ordinarily you should first send the modifications upstream. Ideally upstream will apply the patches and make a release (the easiest way to acomplish objective 1 is for changes to be applied upstream first, so that they can't be forgotten about after being applied to GHC's repo). You can then update GHC's submodule by running
cd libraries/foo git reset --hard some_commit_id cd ../.. git commit -a ./sync-all push
There are some scenarios where you may need to modify GHC's repository without the upstream repository already having the change that you need:
- The maintainer may tell you that they are too busy to deal with the package at the moment, or not be responding at all. In this case, it may be necessary to make changes only to GHC's repositories in the short term, and for the changes to be merged upstream later.
- In a GHC stable branch, we may be using an old version of a library that we need to make a change to, but upstream may only be interested in working on the latest version rather than also maintaining old release branches. In that case, we would only make the change in the GHC respository.
In order to make the change in this case, you
cd libraries/foo git commit -a cd ../.. git commit -a ./sync-all push
Important: If you make a change to a submodule, then make sure you commit in both that repository and the ghc repository before using ./sync-all get or ./sync-all pull. Those commands run git submodule update, which may cause you to lose unrecorded changes.
From the upstream maintainer's point of view
Upstream maintainers don't need to do anything special. You can continue to use any version control system and whatever branching policy works best for you. However, there are two issues to be aware of:
- For libraries that are shipped with GHC, we need to have releases of libraries that can build with that GHC. There may be no suitable existing release (most commonly due to trivial things such as library dependencies needing to be changed, but sometimes due to real changes in other libraries or the compiler), in which case we will request that you make a suitable release or, if it is not convenient for you to do so, we can make one on your behalf (in which case it will normally have only the minimal changes necessary since the previous release).
- Sometimes we may need to make changes to old versions of libraries, as we try to avoid making interface changes within GHC stable branches and upstream development may have moved on since a GHC stable branch was created. When this happens it is up to you whether the changes are sent upstream as normal (and maintained in an upstream branch), or whether they are left only in the GHC repository. Note that if they are made only the GHC repository then we will probably need to make a release from the GHC repository, as per the previous point.